2 Nylon Roller

 

 

Monomer cast nylon is also known as MC nylon. It adopts alkali catalytic polymerisation method to make the polymerisation of already-lactam or other lactam monomers directly in the mould and solidification moulding.
It is an anionic polymerisation reaction technology, the catalyst will be added to the melted lactam monomer at atmospheric pressure in a variety of shapes of moulds for the reaction and trip casting products.
The molecular weight of MC nylon is as high as 70,000-100,000, which is three times that of general nylon 6 and nylon 66. Thus, its comprehensive mechanism performance is much better than other nylon materials, and it is one of the important energy-saving materials vigorously promoted by the National Development and Reform Commission.

MC Nylon is a highly lightweight cast nylon with molybdenum disulphide (Mos2) ultra-fine powder to improve its lubricity. Its exceptional strength supports bearing loads much higher than other engineering thermoplastics. Due to its inherent elasticity, non-polar nature and extremely fast working stress relief, no permanent deformation occurs.MC nylon is wear-resistant and not only reduces the total weight of the equipment, but also protects the mating metal surfaces.

 

 

 

 

MC Nylon Material Characteristics

 

 

 

 

 

 

MC nylon products as one of the engineering plastics, it has a light weight, high strength, self-lubricating, wear-resistant, corrosion-resistant, insulating chips a variety of unique properties. Its coefficient of friction is 8.8 times lower than that of steel and 8.3 times lower than that of copper, and its specific gravity is only one seventh of that of steel.

MC nylon can directly replace the original copper stainless steel, aluminium alloys and other metal products, over the years my company produces MC nylon pulleys, sliders, gears, worm gears, wheels, support wheels, support wheels, pump leaves, bushings, axle tiles, column Shaw, pistons, valve body, rubber plates, pulleys, rotating wheels, rods, tubes, plates, etc., not only to replace the corresponding metal products, and to enable the user to reduce the cost of the whole machine and parts of the city of salt life, economic benefits increased significantly.

MC nylon material is known for its high strength, steel, good toughness, low creep, wear resistance and chemical stability, MC nylon in addition to the characteristics of ordinary nylon materials, due to its high molecular weight, high structural degree, physical and mechanical properties are very excellent, its mechanical strength is three times higher than the general nylon, more than normal engineering plastics.

 

 

 

 

MC 2 nylon roller in the corrosion resistance is quite good, in the rain or humid environment does not rust, will not damage the steel cable due to rust, to the steel cable in the groove of the initial lubrication can be the best use of the results.

 

MC nylon roller self-lubricating and softer than the metal characteristics, so that the roller in contact with the steel cable has a certain degree of toughness, increasing the contact surface of the roller and the steel cable, so that the maximum contact pressure drop, due to the roller toughness is good, accordingly reduce the deformation and distortion of the steel cable and the friction between the steel wire, thereby extending the service life of the overall protection of steel cables.

 

The 2 nylon roller has good toughness, which reduces the deformation and distortion of the steel cable and the friction between the steel wires, thus comprehensively protecting the steel cable and prolonging the service life of the steel cable.

 

MC nylon not only can be connected with steel wire rope, but also, it is more suitable for round sling, wide body sling and other kinds of lifting connection.

 

It can be applied to wear-resistant and sliding parts of mechanical equipment in mines, iron and steel mills, harbours and so on. For example, crane rollers, heavy rollers, lift wheels and universal joint sliders of cold rolling mills, as well as plate shears, rolling plate rollers, panel saw support plates and so on.

 

 

 

 

 

Hot Tags: 2 nylon roller, China, suppliers, manufacturers, factory, customized, Rolling Guide, Heat Radiant Tube, Wire Rod Roll, TC Ring, Polyester Wire Mesh Filter, Steel Guide Rollers